Time to review, recharge and reset.

It's been a busy couple of weeks in the shop, but classes finally ended this past Friday and it's time to review, recharge and reset. 

Maybe relax, too... who knows?

I saw something that caught my eye the other day and checked out a website I'd never heard of - they make high quality zero clearance insert plates for tablesaws.  

The best part? The actual insert is replaceable - so instead of needing the whole plate, your can just replace the 1/4" insert that wears out over time. 

Sweet. 

Ok, maybe that brings out the nerd in me, but this is a big deal. 

When your standard insert is used for a while, the saw blade slot widens. This could come from using different blades, or tilting the blade... but when it's too wide, a couple of things can happen. Your wood can chip out on the bottom of your cut, or worse... a thin strip of wood can slip into the slot, which can jam your dust collector chute. 

Not to mention that it's dangerous to have strips of wood being sucked into your saw. All in all... it's a problem, and Jack Colliflower recognized it. 

At $100, it's not an insert that everyone's going to rush out and get, but I decided to try one at the shop. It came fast - just a day or two after ordering it.

 Well wrapped, 

the plate itself was bundled with a couple of spare inserts. 

The old and the new. It's very nicely machined -  fits perfectly, and looks great. The replaceable 1/4" insert is perfectly cut, and I'll use one of the spares as a pattern to make my own. 

It's branded, so there's no confusion who made it. 

Own it, Jack! 

There are five different set screws that will help level it with the top of your saw. 

The inserts and plates came without instructions on how to cut a new slot, but I've done it a hundred times on other inserts. So I figured that technique would work with this insert. 

To cut a slot on a new zero clearance insert, you bring the fence over the blade, to hold the insert in place when tasing the blade. Make sure that the blade won't hit the fence when you raise it. Then -  flip on the saw and raise the blade,  cutting a perfect slot into your new insert.

I'm not sure if you can tell from this video, but when I raised the blade through the plate, the MDF insert flexed enough to delaminate it, and crack the melamine face. 

Not a disaster, but I had to pull out the insert and glue it back together. In the future, I'll probably support the insert on both sides, so it can't flex as much. 

Or - I'll cut the slot on the saw ahead of time. 

All in all, I give this new insert plate a solid B+ - and if if works like I hope it does, I'll upgrade that to an A.

Stay tuned....

Getting our Mallet on....

Who knew making a mallet could be so fun!

We finished up the mallet class by coming back to the shop and making a few more, just for fun. I'm not sure why, but this really was a satisfying one!

Working with "sentimental" logs

Someone brought me a few "sentimental" logs recently, asking me to turn them into rolling pins. The tree had grown in their yard for decades, and when it was time to cut it down, they couldn't bear to simply discard the wood. Or burn it. 

I've made my fair share of rolling pins out of "sentimental" logs - in fact, one year, a family dropped off a whole trunk full of wood, and asked that I make as many things from the wood as possible. That kept me busy for a while, and it was a fun project, as I had artistic license to make whatever the wood dictated. 

Here's an amazing video with some new technology for wood splitting... this sure would have been helpful when I lived back in Ohio, and spent each Fall splitting wood for the upcoming winter. 

Just a reminder to secure your load....

Saw this on Facebook recently - I've certainly had my fair share of losing loads on the road - but never this bad!

Making a Joiners Mallet

It's been way too long since I blogged, and a few of you let me know that!

I'm thick in the middle of a ton of work, but even more grueling - taking care of business stuff. When you're in business, more than half of your time is taken up by paperwork, dealing with purchases and suppliers, taxes, inventory, maintenance and more. I'm not complaining, but it tends to take more time than the actual woodworking. 

But the good news is - I'm back to a better balance of building more, and pushing fewer papers around my desk. Yay for that. 

We started a mallet making class, and the inspiration for this a 1992 article in ShopNotes,  featuring a simple and effective plan for making one. 

It's a very simple project, but there are so many ways to personalize it, that this doesn't turn into a clone of someone else's mallet. The combinations of wood are endless, and after making one or two, I suspect that everyone will be making another one! 

I made a second one, even heavier than the first; here's the tenon end with two slots for wedging the handle into the head. 

This test fit helps, you don't want to start spreading glue and find out that you need to shave a little more wood down. 

A little glue,

 and some wedges draw everything tight. 

When these are tapped down, the handle is secured tightly in the mortise. 

After the glue sets up, 

they're trimmed off, and everything gets sanded. 

This is really a terrific project, and a little addicting. Like I said - once I made one, I wanted to make a ton, with different wood combinations, sizes, and weights. 

In fact, I was thinking that this would be a fun little business  to start - custom mallets. The next thing I knew - the most recent newsletter from Highland Woodworking came out and it featured a woman doing just that!  

Click on this link to read more about her cool work.

Want to make your own?  Check out this video, which uses the same ShopNotes article that we used.